Difference between revisions of "Precision Pendulum Assembly: Apparatus description"

From wwwelab
Jump to navigation Jump to search
Line 40: Line 40:
 
The shovel maximum speed and acceleration depend on the step-motor power voltage. The higher the voltage the higher the speed and acceleration it can have. In the standard launcher configuration, this voltage is set to 12 V.
 
The shovel maximum speed and acceleration depend on the step-motor power voltage. The higher the voltage the higher the speed and acceleration it can have. In the standard launcher configuration, this voltage is set to 12 V.
  
There are two options to  
+
There are two options that can be adopted to reduce the minimum length of a pendulum:
 +
- sadfds
 +
- sadf
  
  

Revision as of 15:23, 21 November 2020

Apparatus description

The pendulum apparatus is composed of three components: the supporting structure for the pendulum fulcrum, the launcher of the pendulum mass and the controller electronics.

The basic support can be a wall or a robust metallic structure like the one presented here. The choice for the bob was a training steel weight from the official shot put with 2kg. This weight has the advantage of having a drilled hole for holding an M4 screw and can be found in any good sports shop. This screw can be made of a threaded brass rod with 10mm length. A small 1mm hole is drilled on the rod were the pendulum cable is fixed using current soldering thin-plumb(or any silver-thin alloy) or by tying a proper knot. The cable used is from 0.4mm remanium wire that can be bought in any dentistry retailer.

The following drawings document the construction of the metallic pendulum's sections.

World Pendulum standard manufacturing drawings
Pendulo mundial vista.png
Pendulo apoio.png
Pendulo topo.png
Pendulo base.png
Pendulo fulcro.png


The support for the fulcrum is made from any robust and hard flat surface as for instance a brass or stainless steel piece with a 12-16mm hole. This surface has an indentation made with a diamond or hard steel blade which holds the pivot in place. With this design, slippage is avoided.

The fulcrum itself is made as well of stainless steel or brass consisting in a triangular prism with 50mmx9mm with a central 1mm hole in one face crossing the opposite edge. In this hole is soldered or glued an intravenous needle where the pendulum cable goes through and is secured by a small screw on the top.

Pendulum holder showing the pivot support structure for the 50mmx9mm triangular pyramid.
Pendulum string support to avoid elongation errors. The cable is fixed by soldering it into an M4 brass screw 40mm long or an intravenous needle.
Pendulum string fulcrum detail showing the screw to hold the wire. Remanium is very ductile and easily wound around the screw.
Fulcrum support structure to be held on top of the pyramidal pendulum support. Strong M6 or M8 screws are used.

Pendulum length limits

The launcher of the pendulum and controller electronics have limits which restrict the pendulum length and/or operation of the Precision Pendulum Assembly. Each one of those limits (min. and max.) are explained in the following subsections below. The last subsection (Limits) presents a table with the limits for the standard launcher and controller electronics used in the World Pendulum Alliance (WPA) apparatus assemblies.

Minimum length

The minimum length of the pendulum is limited by the launcher speed. For a given launching distance, the shorter the pendulum the higher is the horizontal pendulum velocity. Therefore, the shovel acceleration should be high enough to make a clean release of the ball and the shovel speed should be high enough to make sure the ball never touches the shovel after it has been released. The shovel maximum speed and acceleration depend on the step-motor power voltage. The higher the voltage the higher the speed and acceleration it can have. In the standard launcher configuration, this voltage is set to 12 V.

There are two options that can be adopted to reduce the minimum length of a pendulum: - sadfds - sadf


Maximum length

Limits

A photo of the launcher used in the WPA is shown in the figure below. This launcher uses a V-slot rail technology and it is characterized by a maximum horizontal launching distance of 250 mm. The following table shows the pendulum length limits for this specific launcher.



Next Page (Mechanical assembly)