Difference between revisions of "Dielectric effect in a Cilindric Capacitor"

From wwwelab
Jump to navigation Jump to search
Line 19: Line 19:
  
 
=Experimental Apparatus=
 
=Experimental Apparatus=
[[File:condensador-seccao.png|thumb|Figure 2: Sectioned schematic of the capacitor, where a=12mm and b=14mm]]
+
[[File:condensador-seccao.png|thumb|Figure 2: Sectioned schematic of the capacitor, where a=12mm and b=16mm]]
  
The capacitor is made from a copper tube with 12mm outer diameter and 200mm length (inner plate), having been outfitted with a Polystyrene dielectric to a certain length. This is enclosed in a second copper tube with 14mm inner diameter (outer plate) that moves along the first, thus acting as the plates of a variable capacitor. This way, the area of the capacitor corresponds only to the parts where the two cylinders overlap.
+
The capacitor is made from a copper tube with 12mm outer diameter and 200mm length (inner plate), having been outfitted with a Polystyrene dielectric to a certain length. This is enclosed in a second copper tube with 16mm inner diameter (outer plate) that moves along the first, thus acting as the plates of a variable capacitor. This way, the area of the capacitor corresponds only to the parts where the two cylinders overlap.
  
 
Note that, because of set-up constraints, there is a "minimum" capacitor of 26mm. In other words, x=0 actually corresponds to a cylindrical capacitor with 26mm length and Polystyrene dielectric.  
 
Note that, because of set-up constraints, there is a "minimum" capacitor of 26mm. In other words, x=0 actually corresponds to a cylindrical capacitor with 26mm length and Polystyrene dielectric.  

Revision as of 18:39, 21 March 2013

Description of the Experiment

Figure 1: Photo of the experimental setup

This experiment's purpose is the determination of the capacity of a variable coax cylindrical capacitor. It has two sections, a first with a Polystyrene dielectric, and a second with air, allowing the determination of the relative dielectric constant of Polystyrene.


Ligações

  • Video: rtsp://elabmc.ist.utl.pt/condensador.sdp
  • Laboratory: Advanced in e-lab.ist.eu[1]
  • Control room: Condensador Cilíndrico
  • Level: ****


Experimental Apparatus

Figure 2: Sectioned schematic of the capacitor, where a=12mm and b=16mm

The capacitor is made from a copper tube with 12mm outer diameter and 200mm length (inner plate), having been outfitted with a Polystyrene dielectric to a certain length. This is enclosed in a second copper tube with 16mm inner diameter (outer plate) that moves along the first, thus acting as the plates of a variable capacitor. This way, the area of the capacitor corresponds only to the parts where the two cylinders overlap.

Note that, because of set-up constraints, there is a "minimum" capacitor of 26mm. In other words, x=0 actually corresponds to a cylindrical capacitor with 26mm length and Polystyrene dielectric.


Protocol

Determination of the relative dielectric constant

Take two sets of experimental data, one covering the Polystyrene area and the other covering air. The end-points of the sweep should be chosen in a way that allows a precise determination of the slope of the graphical representation. This slope will give the relation between the capacity and the length of the capacitor (each set referring to its corresponding dielectric). The ratio between the two slopes will give the relative dielectric constant for PVC.


Advanced Protocol

Determination of the dielectric constant of air

Considering Gauss's law, it is possible to determine the capacity of the cylindrical capacitor, using the formula:

\[ C = \frac{ 2 \pi \epsilon _0 }{ ln(\frac{b}{a}) } L \]

By doing a linear regression with the data from the section of the capacitor without the dielectric (which means the air acts as the dielectric) it is possible to accurately determine the value of the capacity. From this, reversing the formula, the air's permittivity can be found (close to vacuum, i.e. \( \epsilon _0 \)).


Links